Home > Hp Prodesk > Hp Prodesk 400 G2 POST Error

Hp Prodesk 400 G2 POST Error

After test completes, press f10 key to Save and Exit, and then press Enter key to Exit Saving Changes. Will see. top Provide feedback Please rate the information on this page to help us improve our content. Component caused system to hang and/or reboot. http://hamlookup.com/hp-prodesk/hp-prodesk-600-g2-bios.html

When troubleshooting further, please refer to the section What to do when beep codes occur . LED and beep condition Description Corrective action Power button LED blinks 5 times with 5 beeps Memory Reseat memory DIMM modules. Listen for sounds of drives and fans turning. top Finding repair service Many of the problems associated with LED or beep codes require service or parts replacement.

A basic function might be reading memory, displaying video, or being able to send information to a hard drive. The information in this document is subject to change without notice. Reseat component.

And if the issue persisted, I hope you asked for a full refund! Verify fan(s) are working as expected. If the error persists, replace the system board. Verify system fan(s) are working.

Test with known good memory. Reply 0 0 MikeDem Honor Student Posts: 2 Member Since: ‎02-28-2014 Message 7 of 23 (1,209 Views) Report Inappropriate Content Re: Prodesk 400 G2 Microtower - after latest bios update received NOTE: See the Services Media Library for steps for your computer. NOTE: For more information on Computer Setup, see POST numeric codes and text messages This section covers those POST errors that have numeric codes associated with them.

Nudging the pin with long nose pliers and a small screw driver fixed it and allowed the connector to be plugged in all the way and all is well. Thermal 4.2 A processor over temperature condition has been detected.* CPU overheat is detected. You can use this information in the next step when performing the troubleshooting. New bios has a security feature that prevents going back to old bios.New Bios seems to be setup for G1 models - ie.

In the BIOS Setup Utility, use the Right Arrow or Left Arrow keys to navigate through the menu selection to locate the Diagnostics. Got it, continue to print 2012-2017 ManualsLib.com About Us About ManualsLib Privacy Policy F.A.Q. Sign up! Use these codes before referring to the other codes when they occur.

If a beep code occurs the problem is likely occurring before the system can display video (check the video card or memory). http://hamlookup.com/hp-prodesk/hp-prodesk-600-g1-sff-specs.html Really hate to box up and send back. If able, test known good CPU. Replace the rear chassis fan.I would reseat the fan cable/connector to the motherboard and make sure nothing is rubbing the fan causing it to slow down or stop.

DMA or timers. Verify the correct ROM. 2. Have the same problem on 2 PC .. http://hamlookup.com/hp-prodesk/hp-prodesk-600-g1-bios-key.html Replace component or system board as needed.

NOTE: For more information on Computer Setup, see POST numeric codes and text messages This section covers those POST errors that have numeric codes associated with them. Reset CMOS. Just hope we don't have to keep replacing the motherboard every year. 0 0 « Previous 1 2 Next » « Message Listing « Previous Topic Next Topic » Note on

Restore password × Upload manual upload from disk upload from url Thank you for your help!

What Our Users Say Press & Media Contacts Advertising DMCA Policy Brands × Login Login to ManualsLib Don't have an account? Flash the ROM if needed. 3. RESOLUTION To resolve this issue, download and install the following SoftPaq: SoftPaq Description Release Notes Download SoftPaq HP Business Desktop System BIOS (L02) Version: 02.47 Revision: A Pass: 1 SP76380 release Since I have a SDD I didn't hear the computer come on - I was lucky not to short something out!

If an expansion board was recently added, remove it to see if the problem remains. 4. The default mode is POST Message Disabled. Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions contained herein. navigate here Replace the system board. 1.

Replace CPU. Reseat component. Press the Power button to start the computer and repeatedly press the f10 key to enter the BIOS Setup menu.